How are DStv recordings done? ITEM 1 & 2 are explained above.; ITEM 3 is recording programs using your Tv Guide, and is done by using the Tv Guide button on the remote (A9 and older) to get your tv Guide on the screen. Then you can move the highlighted area up, down left or right with your cursors (arrow) buttons. Going right advances the time & Press the DStv button on your remote and switch to “Menu”.Go to [HOST] the “Parental Control” [HOST] “PG Settings” and open [HOST] to unlock [HOST] down to “Change PIN”. How do I unlock my DStv Explora A7 remote? STEP 1: Press and hold Standby and Options buttons together until the LED blinks red twice To fix this, follow the steps below: Pry open your remote from the lining on the side. Carefully pick out the electronic board and clean it with a soft clean cloth dipped in alcohol or water. Leave them in the open air for a few minutes to dry. You can also use your standing fan to make it dry quicker Here are the steps: Find the power cable at the back of the device and unplug it from the socket. Wait for about a minute before plugging the device back in. Press the power button on the device or the remote to turn the device back on. The device will start up again, and the default channels will load. Your Dstv Explora has now been rebooted On your A7 remote Blue DStv button to access DStv Central. STEP 2. Using the left and right navigational buttons, go to Settings. STEP 3. Use the up and down navigational buttons to find Satellite Settings. STEP 4. Navigate to Additional Networks and press OK. On the Additional Networks, there are Networks numbered from 1 – 5 DStv’s new Explora Ultra brings the best of two worlds together by introducing streaming apps to the popular DStv Explora, adding depth to the entertainment offering available. It offers all the much-loved PVR features from previous models, including the ability to record, rent movies from BoxOffice and Catch Up on favourites K views 3 years ago. Connect your DStv Explora to the internet and get even more out of your DStv. Follow these steps to set up your
DStv Remote Controls
How do I set the time on my DStv Explora 3a? The DStv Explora settings for adjusting the time are available on the DStv menu. Press the DStv button to bring up the main menu. Click on the advanced options and select the local time option. You can now get the option to change the time depending on your local time. How do I get to my DStv When a TV link is plugged in and it does not want to power-on or function properly, the steps below should be followed. Press menu button. Select advanced option. Enter the pin Select equipment setup. Select no.3 on the menu (TV Link/Auxiliary) There will be two options on/off, this option must be set to on It is a simple process, and you can find the guide in your decoder manual. To check the status from the XtraView settings menu, first, click on the help option. It will bring up a menu, and you can click on the general information option. Among the options available here is the extra view status check, and you can click on it Equipment needed. Connecting Explora Decoder using a Smart LNB. How to connect two DStv Explora decoders with extra view. How to connect an Make sure that your router is switched on and connected to the internet. Switch your TV on. Plug one end of the Ethernet cable into the clearly marked Ethernet port (the green one) at the back of your Explora. Plug the other end of the Ethernet cable into any of the Ethernet ports at the back of your router Use that port to connect the RG6 cable from the dish. Run the installation wizard. Once you have connected the Explora decoder correctly to the satellite dish, run the installation wizard. Follow the steps in the wizard and make sure to use Quick Setup. You should wait for the three tuners to show blue bars of the signal before you initiate the
One For All DStv A7 Explora Remote - Makro
2 Press the blue DStv button on your DStv Explora remote Scroll to Settings Select System Settings Select Connectivity Set-up Connect the cable on the docking station to the USB port on the back of your DStv Explora (if your Explora has a USB port on the side, don’t use that one). Insert the DStv WiFi Connector into the docking station This shows you how to link your dstv A7 remote control to your [HOST]ble controls areTV power buttonVolume up/downHelps to reduce the burden of holding mo Series recording makes sure you won’t miss an episode. *HD and Dolby on selected channels. Recommended retail price - R without installation / R with DStv Remote Controls. Select a remote below to download the user manual. User Manuals. B5 Remote Control Quick Guide. A5 Remote Control Quick Guide. A6 Step 6 Wait two minutes. The Wireless LED on the front of the DStv WiFi Connector should light up (solid white) once an internet connectionhas been established. If the Wireless LED on the front of the DStv WiFi Connector is solid amber, the internet connection is weak. To ˜x this, move the DStv Remote (A6 model) 7 If the green lights blink below both i and BACK, the remote is in mode 3. To set the remote to mode 3: press and hold both the i and BACK buttons for 3 seconds or until you see the green light blink on 1 and 2 (below the i and BACK buttons). IMPORTANT The DStv Explora must be set up to “listen” for the correct mode